Redoing incorrect terminations or pulling new wiring wastes tremendous amounts of time and money. As a result, wire pairs are often routed and terminated incorrectly the first time. With traditional analog toners and probes, isolating individual wire pairs precisely can be almost impossible because of signal bleed between pairs. IntelliTone™ eliminates hours of cable confusion-and you can count on getting it right the first time. The smart digital signal processing in the IntelliTone™ Pro Probe clearly identifies this signal with audio and LED visual indicators, allowing you to rapidly isolate the correct cable from a bundle or on a patch panel. The IntelliTone™ Pro Toner uses the unique properties of twisted pair cabling to create a balanced signal that minimizes the effect of signal bleed. This provides telecom technicians a decisive way to identify individual wire pairs before punching them down on a jack or a block, or when diagnosing voice transmission problems. The SmartTone analog signal will change ‘songs’ each time the pair under test is shorted together. SmartTone analog toning eliminates frustrating guesswork locating individual wire pairs during installations. In high-interference environments, digital may still be a better choice. It should also be used in areas with relatively low interference from electronic devices. These cables are optimized for lower frequency transmissions, and therefore are more easily isolated with a low-frequency tone. IntelliTone Pro’s SmartTone analog toning can be used on voice-grade cabling (Cat 3 and below), as well as coax, security/alarm, and speaker wiring. It eliminates the need for both a toner to a wiremapper, and provides 100% confirmation that the right cable has been located. The benefit of this wiremap test is two-fold. The IntelliTone Pro 200 probe has an RJ45 input port and CableMap feature, allowing it to be plugged directly into a patch panel or wall port. ![]() That means LAN cabling technicians can quickly zero in on the right cable during installations or troubleshooting.ĭigital toning is especially helpful once the cable has been located as it displays cable wiremap and checks for shorts, opens and miswires. This allows the tone to overcome competing data signals and aggressive low-frequency terminations of Ethernet switches. It operates at a high-frequency to match the higher frequency data the cable plant is designed to carry. IntelliTone Pro’s digital encoded signal should primarily be used on high-grade data cabling (Cat 5e/6/6a), and in active network environments. IntelliTone Pro changes that by combining cutting-edge digital and analog signaling to locate and verify virtually any copper cable, regardless of application or environment. ![]() Until now, no single tool has combined the right technologies to operate across all copper media types, and in all environments. Verifying proper routing and termination of this diverse set of cabling types requires tools optimized for different frequencies, connector types, and work environments. Most buildings have a combination of telephone, twisted-pair data, coax, and security/alarm wiring. Today’s media networks are more diverse than ever. Only IntelliTone™ Pro Toners and Probes offer the powerful combination of digital and analog technologies to resolve common infrastructure problems that arise during installing, maintaining, and changing of your network. This network cable toner and probe's breakthrough digital technology makes it the first tool to tone and trace safely and effectively on active networks. The IntelliTone™ Pro 200 LAN Toner and Probe Series from Fluke Networks gives you superior vision for tracing and locating cables hidden in floors, ceilings, walls, and in bundles. ![]() Use analog mode to isolate individual wire pairs, and trace voice, audio, and video cabling. Use digital mode to trace and locate data cabling safely and effectively on active networks. That means it’s equipped with the most powerful cable tracing and location technologies for any work environment. The IntelliTone™ Pro 200 LAN Toner and Probe Series from Fluke Networks is the first network cable toner tracer and probeto offer digital and analog signaling all in one network toner and probe. Our new IntelliTone Pro 200 LAN Toner and Probe Kits finds the cables others can't. Get advanced vision for tracing and locating network cables more effectively at patch panels, switches, termination blocks, or hidden within bundles.
0 Comments
Leave a Reply. |